Description
25.4mm x 3.2mm (1" x 1/8") Brass Flat Bar
The 25.4mm x 3.2mm (1" x 1/8") Brass Flat Bar is solid rectangular brass flat bar supplied cut to length.
It is available cut to your required length for fabrication, engineering and project use. Please review the grade, finish and suitability information below before ordering.
Technical Specifications
| Material | Machinable brass |
|---|---|
| Product family | Brass Flat Bar |
| Material grade | May be supplied as CW614N (CZ121 / CuZn39Pb3) or CW623N (CZ130 / CuZn43Pb2), depending on size, supplier and current stock. |
| Applicable standard | BS EN 12167 where applicable to the supplied product |
| Finish | Mill or drawn finish with normal handling marks and natural tarnishing. |
| Cutting service | Cut to your required length |
| Standard cutting tolerance | ±3 mm |
| Edge condition | Supplied as-cut and not deburred |
Key Features
- Solid rectangular brass profile
- Good machinability with suitable tooling
- Available cut to your required length
- Suitable for fabrication using an appropriate process
- Useful for professional, trade and general engineering work
Benefits
- Good machinability with suitable tooling
- Attractive non-ferrous appearance
- Cut-to-length ordering can reduce material waste
Material Grade Information
This product may be supplied in one of the following machinable brass grades, depending on product size, supplier and current stock:
- CW614N, traditionally known as CZ121, material designation CuZn39Pb3
- CW623N, commonly associated with CZ130, material designation CuZn43Pb2
The grade information shown is general supply information and does not guarantee that a particular grade, certificate or traceability will be supplied for an individual order.
If a particular material grade, certification or traceability is essential, please contact KI Metals before placing your order and obtain written confirmation from KI Metals.
Telephone conversations, verbal discussions, customer order notes, drawing notes and other instructions submitted with an order do not constitute written confirmation of material grade or certification requirements.
These machining brass grades normally contain lead as an alloying element. If lead content, regulatory compliance or suitability for a particular application is important, written confirmation must be obtained before ordering.
Surface Condition
Mill or drawn finish with normal handling marks and natural tarnishing.
Normal production, storage, handling and cutting variations are not automatically evidence of a product defect. If appearance is critical, contact KI Metals before ordering.
Typical Applications
- Decorative Trim
- Shims And Spacers
- Machined Components
- Light Fabrication
Design and Suitability
Product selection must not be based on dimensions alone. The required grade, loading, environment, connections, fabrication process and installation method should be specified or checked by a suitably qualified person where applicable.
KI Metals supplies material to the dimensions ordered but does not determine whether a particular item is suitable for the intended load, environment or application.
Cut to Your Required Length
Enter your required measurement in the Length box before adding the product to your basket. Material is cut to the ordered length with a standard cutting tolerance of ±3 mm.
Products are supplied as-cut and are not deburred. Contact KI Metals before ordering if a tighter tolerance, specific end preparation or additional processing is required.
Also Known As
- Brass Flat Bar
- Brass Strip
- Machinable Brass Flat
Fabrication and Safety
Use suitable tooling and control sharp swarf, chips and cut edges. The listed free-machining brass grades normally contain lead, so machining dust, fumes and residues must be controlled using appropriate extraction, hygiene procedures and personal protective equipment.
Confirm composition and regulatory suitability in writing before fabrication where lead content, drinking-water contact, food contact or another controlled application is relevant.
Frequently Asked Questions
Is a particular material grade guaranteed?
No. Brass flat bar may be supplied as CW614N (CZ121 / CuZn39Pb3) or CW623N (CZ130 / CuZn43Pb2), depending on size, supplier and current stock. A particular grade, material condition, certificate or traceability is only guaranteed where KI Metals confirms it in writing before the order is placed. Telephone conversations, verbal discussions, drawing notes and order notes are not confirmation.
Can I request a grade or certificate in the order notes?
You may provide information in the order notes, but an order note does not constitute confirmation. Contact KI Metals before ordering and obtain written confirmation.
Can this item be cut to my required length?
Yes. Enter the required measurement in the Length box before adding the product to your basket. The standard cutting tolerance is ±3 mm unless confirmed otherwise.
Is the material suitable for my project?
The customer is responsible for confirming material grade, dimensions, loading, environment, fabrication method and regulatory requirements. Structural or safety-critical selection should be checked by a suitably qualified person.
Safety Notice
Wear suitable gloves, eye protection and other appropriate personal protective equipment. Ensure the product is correctly supported and secured during storage, lifting, cutting, fabrication, transport and installation.
Reviews
There are no reviews yet.